公司新聞

濟南水穩料對壓路機有什么要求？

來源：http://www.dotomui.com/ 日期：2025-05-19

　　在道路基層施工中，水穩料（水泥穩定碎石）與壓路機的關系，猶如琴弦與演奏家的共鳴——唯有精準匹配，才能奏出密實度的“完美樂章”。水穩料的粒徑級配、含水量與水泥劑量，決定了壓路機的選型、操作方式與性能邊界。這種“默契配合”，既是對材料科學的尊重，也是對施工藝術的詮釋。

　　In the construction of road subgrade, the relationship between water stabilized materials (cement stabilized crushed stones) and rollers is like the resonance between strings and musicians - only precise matching can play the "perfect melody" of compactness. The particle size distribution, moisture content, and cement dosage of water stable materials determine the selection, operation mode, and performance boundary of road rollers. This kind of 'tacit cooperation' is not only a respect for material science, but also an interpretation of construction art.

　　第一重匹配：壓路機類型與水穩料特性的“對話”

　　First Matching: Dialogue between Roller Type and Water Stable Material Characteristics

　　水穩料的骨料粒徑（通常5-31.5mm）與級配曲線，直接決定了壓路機的“體型”。對于粗骨料含量超過60%的級配，需選用自重≥18噸的振動壓路機，其激振力可穿透骨料間隙，形成“骨架密實”結構；而細骨料占比高的水穩料，則更適合輪胎壓路機，通過柔性揉搓減少離析風險。

　　The aggregate particle size (usually 5-31.5mm) and grading curve of water stable materials directly determine the "shape" of the roller. For gradations with a coarse aggregate content exceeding 60%, a vibratory roller with a self weight of ≥ 18 tons should be selected, whose excitation force can penetrate the gaps between the aggregates and form a "skeleton dense" structure; Water stable materials with a high proportion of fine aggregates are more suitable for tire rollers, reducing the risk of segregation through flexible kneading.

　　更關鍵的是壓路機的工作寬度。水穩層攤鋪寬度每增加1米，壓路機需延長0.3米的碾輪寬度，以避免邊緣漏壓。這種“寬度適配”原則，如同為攤鋪機與壓路機定制“情侶裝”，確保壓實無死角。

　　More importantly, the working width of the roller. For every 1 meter increase in the paving width of the water stable layer, the roller needs to extend the roller width by 0.3 meters to avoid edge leakage. This principle of "width adaptation" is like customizing "couple outfits" for pavers and rollers, ensuring that there are no dead corners in compaction.

　　第二重匹配：振動參數與水穩料響應的“共振”

　　Second Matching: Resonance between Vibration Parameters and Water Stable Material Response

　　壓路機的振動頻率與振幅，是激活水穩料密實度的“鑰匙”。頻率需與骨料粒徑成反比——粒徑越大，頻率越低（通常25-35Hz），以避免骨料破碎；振幅則需與水穩料厚度成正比——每10cm厚度需對應0.5mm振幅，確保振動波能穿透至底層。

　　The vibration frequency and amplitude of the roller are the key to activating the compactness of water stable materials. The frequency should be inversely proportional to the particle size of the aggregate - the larger the particle size, the lower the frequency (usually 25-35Hz) to avoid aggregate crushing; The amplitude should be proportional to the thickness of the water stable material - every 10cm thickness should correspond to an amplitude of 0.5mm to ensure that the vibration wave can penetrate to the bottom layer.

　　這種“共振”效應在復壓階段尤為關鍵。當壓路機以1.5-2.0km/h的速度行駛時，振動輪與水穩料產生“同步振動”，使骨料重新排列，空隙率降低至15%以下。而終壓階段的靜碾，則如同“定型錘”，將密實度鎖定在98%以上。

　　This "resonance" effect is particularly critical during the re compression stage. When the roller travels at a speed of 1.5-2.0km/h, the vibrating wheel and the water stabilized material produce "synchronous vibration", causing the aggregate to rearrange and the void ratio to decrease to below 15%. The static rolling in the final pressing stage is like a "setting hammer", locking the compactness above 98%.

　　第三重匹配：行駛速度與壓實遍數的“黃金比例”

　　Third Matching: The "Golden Ratio" between Driving Speed and Compaction Times

　　壓路機的行駛速度與壓實遍數，存在一個“黃金比例”。初壓速度需控制在1.5km/h以內，確保水穩料初步穩定；復壓階段可提升至2.5km/h，但每遍壓實需重疊30cm輪寬，形成“碾壓帶”；終壓速度則回落至2.0km/h，以消除表面輪跡。

　　There is a "golden ratio" between the driving speed of a road roller and the number of compaction passes. The initial pressing speed should be controlled within 1.5km/h to ensure the initial stability of the water stable material; During the compaction stage, the speed can be increased to 2.5km/h, but each compaction layer needs to overlap the wheel width by 30cm to form a "rolling belt"; The final pressure speed will drop back to 2.0km/h to eliminate surface wheel marks.

　　更精細的管控涉及“時間窗口”。水穩料從攤鋪到終壓的時間需控制在2小時內，否則水泥初凝將導致壓實度下降。這種“速度與時間的博弈”，要求壓路機操作手兼具經驗與精準度。

　　More precise control involves a 'time window'. The time from spreading to final compaction of water stable materials should be controlled within 2 hours, otherwise the initial setting of cement will lead to a decrease in compaction degree. This' game of speed and time 'requires the roller operator to have both experience and precision.

　　第四重匹配：含水量與壓路機操作的“濕度平衡”

　　Fourth Matching: Moisture Balance between Moisture Content and Roller Operation

　　水穩料的含水量（通常比最佳含水量高0.5%-1%）是壓實質量的“隱形指揮棒”。含水量過高時，壓路機需降低振幅并減少遍數，防止“彈簧土”現象；含水量過低時，則需在復壓前補水，再通過輪胎壓路機的揉搓促進水分均勻分布。

　　The moisture content of water stable materials (usually 0.5% -1% higher than the optimal moisture content) is the "invisible conductor" of compaction quality. When the moisture content is too high, the roller needs to reduce the amplitude and the number of passes to prevent the phenomenon of "spring soil"; When the moisture content is too low, it is necessary to replenish water before re pressing, and then promote even distribution of moisture through the rolling of the tire roller.

　　這種“濕度平衡”在高溫干燥環境中尤為挑戰。此時需采用“霧狀補水”技術，將水霧化至50微米粒徑，避免局部積水導致離析。

　　This' humidity balance 'is particularly challenging in high-temperature and dry environments. At this time, the "mist like water replenishment" technology should be used to atomize the water to a particle size of 50 microns to avoid local water accumulation and segregation.

　　第五重匹配：壓路機維護與壓實質量的“長期契約”

　　Fifth Matching: Long term Contract for Roller Maintenance and Compaction Quality

　　壓路機的維護狀態，是壓實質量的“隱性保障”。振動軸承的徑向間隙需控制在0.1mm以內，否則將導致振幅衰減；輪胎壓路機的胎壓需保持恒定（誤差≤2%），否則將影響揉搓效果。

　　The maintenance status of the road roller is the "implicit guarantee" of compaction quality. The radial clearance of the vibration bearing should be controlled within 0.1mm, otherwise it will cause amplitude attenuation; The tire pressure of the tire roller should be kept constant (error ≤ 2%), otherwise it will affect the kneading effect.

　　更關鍵的是“壓路機-水穩料”的適應性磨合。新購壓路機需經過50小時的“走合期”，在此期間避免高強度作業，使機械部件與材料特性逐步匹配。

　　More importantly, the adaptive running in of the "roller water stabilized material" is crucial. The newly purchased roller needs to go through a 50 hour "running in period" to avoid high-intensity operations and gradually match the mechanical components with the material properties.

　　壓實是材料與機械的“雙人舞”

　　Compaction is the 'duet' of materials and machinery

　　水穩料對壓路機的要求，本質是對施工系統的深度理解。它要求從業者兼具材料學家的嚴謹與機械師的敏銳，在參數匹配與操作細節中構建起質量、效率與耐久性的平衡。當壓路機與水穩料形成“默契共振”時，我們看到的，是道路施工從“經驗驅動”向“科學管控”的進化。這種進化，無關未來想象，而是對當下標準的極致追求。

　　The requirements of water stable materials for rollers are essentially a deep understanding of the construction system. It requires practitioners to combine the rigor of materials scientists with the sensitivity of mechanics, and to establish a balance between quality, efficiency, and durability in parameter matching and operational details. When the roller and water stabilized material form a "tacit resonance", what we see is the evolution of road construction from "experience driven" to "scientific control". This evolution is not about imagining the future, but about the ultimate pursuit of current standards.

　　本文由濟南水穩料友情奉獻.更多有關的知識請點擊:http://www.dotomui.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Water Stable Mixing Plant For more information, please click: http://www.dotomui.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.

上一條：濟南挖掘機租賃有什么優勢所在？

下一條：